Small Room Ideas – How to Turn a Closet into a Home Workshop - World Axiom Ltd. (2023)

Small room ideas abound on the internet. I’ve spent years searching Pinterest to see what people do to make their own “space”, be it a home craft room, man cave, small sewing area, etc. I saved hundreds of pins hoping one day I would have a space to call my own.

After moving to our new home, I had a chance to do just that. Family members had staked out their claims for space in the house. Room after room slipped from my grasp until there was just one room left. But it would work for me. It was an outside closet that held:

Let's quickly go over the destruction part of the project.

1. First, clear out the chemicals; they were definitely a health hazard.
2. Rip the racks out that had begun to dissolve from years of neglect.
3. Throw out the rusted water tank and water softener tank
4. Move the pool pump and sand filter outside.
5. Relocate the pressurization tank into the corner and wall mount the water filter.
6. There was nothing I could do about the HVAC unit; I was not in the mood to spend 10,000 USD on something that was working fine.

The photo below shows the space I had to work with after the tear out. This is where I would build my own home workshop. All those Pinterest photos showing ideas for small rooms really helped.

How To Turn a Small Space into Your Ultimate Home Workshop

The concrete floor was partially exposed; half still had an epoxy paint on it.

The walls had plenty of holes that needed to be patched.

Now for What I have Been Dreading…

Stripping the epoxy paint off the floor.

I had stripped floors with my father once, years ago. It was not pleasant experience. I was already getting flashbacks to that day.

Fristt thing was to get all the tools and protective gear organized.

Based on what my father, a store clerk at Home Depot and every contractor I spoke with said I must do to get rid of the epoxy paint, I loaded up to do this like I was cleaning up a hazardous waste dump. KEEPING THE ROOM WELL VENTILATED WITH FREQUENT REST WILL KEEP YOU ALIVE!

Respirator and hazmat suit engaged. Off we go.

The two cans of Klean Strip Premium Stripperwere not enough nor strong enough. I switched to the thick paste in the big can.

A key point to remember in stripping the floors is to let the stripper do the work. Put it on thick over the section you are working on and get out of the room!

Drink fluids while waiting because you are going to be sweating in that suit.

Once the paint bubbles up, use a scraper and dump the sludge in a thick plastic pail. The goo will eat through a plastic bag and will also trash your footwear. I used a pair of sneakers that were destined for the trash heap.

Strip, scrape and repeat until all the paint is off the floor and you are left with just raw concrete.

I then thoroughly washed and rinsed the floor, making sure all the stripper was gone.

I painted the ceiling next. 3M Scotch Blue painter’s tapewent around the fixtures I couldn’t remove and along the top wall edge, for clean lines.

The paint is Sherwin Williams Property Solution White Latex paint. I cut in the edges with a 2 ½” brush and then used the roller. It only needed one coat to cover the ceiling.

Put a plastic drop cloth over the floor since I didn't want to strip fresh paint off the floor.

It was a little humid, so I waited two days for the paint to dry. The central air vent helped the paint to dry and also kept the humidity down.

Once the ceiling was dry, I peeled the painter’s tape off. I really like the 3M Scotch Blue because it doesn’t take any of the under paint off and peels off easily but keeps a clean edge.

Painting the Walls and Pegboard

First, the painters tape went up on the ceiling edge.

I used Sherwin William’s Infinite for the walls and hoped the salesman’s comments and the marketing efforts written on the can weren’t kidding and I wouldn’t need a second coat.

Grabbed the 2 ½” brush and cut around the edges, electrically boxes, ceiling and pipes on the wall. This took a lot longer than the ceiling because there was more surface area and a lot more areas the roller couldn’t reach.

When rolling the pegboard I recommend not soaking the roller in the paint. Better to go over the pegboard holes with a “dryer” roller so that the paint doesn’t slop in the holes. Otherwise, you are going to be picking out paint for days!

I did need a second coat in spots on the pegboard because I kept a minimal amount of paint on the roller. In my opinion, worth it.

Prepping the floor

Some of the concrete was broken after sitting underneath the hot water tank and other pumps for years. I used a wire brush to get the loose concrete off and then patched the wall and some chips in the floor with DAP Flexible Floor Patch and Leveller. A putty knife kept it flat and smooth; it dried the same way.

A few days later the primer was fully dry and I painted the floor with Valspar Porch Floor, and Patio. Used dark grey to help hide dirt.

If I could have done it differently I would have used a paint with some texture. The floor is very, very smooth now. When it is humid the floor almost feels slick.